smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.12.14-200.fc25.x86_64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Maxtor DiamondMax Plus 9 Device Model: Maxtor 6Y160M0 Serial Number: Y48C1BWE Firmware Version: YAR51HW0 User Capacity: 163,927,522,816 bytes [163 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 0 Local Time is: Fri Oct 13 23:52:32 2017 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 302) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 72) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0027 205 201 063 Pre-fail Always - 13190 4 Start_Stop_Count 0x0032 252 252 000 Old_age Always - 2316 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0 7 Seek_Error_Rate 0x000a 253 239 000 Old_age Always - 0 8 Seek_Time_Performance 0x0027 249 238 187 Pre-fail Always - 33632 9 Power_On_Minutes 0x0032 177 177 000 Old_age Always - 193h+15m 10 Spin_Retry_Count 0x002b 253 249 157 Pre-fail Always - 0 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 246 246 000 Old_age Always - 2772 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0 193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0 194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 47 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 3623 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 248 000 Old_age Always - 29 202 Data_Address_Mark_Errs 0x000a 253 252 000 Old_age Always - 0 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 2 204 Soft_ECC_Correction 0x000a 253 252 000 Old_age Always - 0 205 Thermal_Asperity_Rate 0x000a 253 252 000 Old_age Always - 0 207 Spin_High_Current 0x002a 253 249 000 Old_age Always - 0 208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0 209 Offline_Seek_Performnce 0x0024 194 192 000 Old_age Offline - 0 99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 SMART Error Log Version: 1 Warning: ATA error count 23 inconsistent with error log pointer 5 ATA Error Count: 23 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 23 occurred at disk power-on lifetime: 24471 hours (1019 days + 15 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 c0 ce e8 e9 Error: ICRC, ABRT at LBA = 0x09e8cec0 = 166252224 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 c0 ce e8 e9 00 1d+12:29:24.336 READ DMA c8 00 08 e8 d2 09 e0 00 1d+12:29:24.320 READ DMA c8 00 60 48 12 cc e0 00 1d+12:29:24.320 READ DMA c8 00 80 c0 11 cc e0 00 1d+12:29:24.320 READ DMA c8 00 08 c0 c9 09 e0 00 1d+12:29:24.304 READ DMA Error 22 occurred at disk power-on lifetime: 12569 hours (523 days + 17 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 67 ce 06 e0 Error: UNC 8 sectors at LBA = 0x0006ce67 = 446055 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 67 ce 06 e0 00 00:04:46.304 READ DMA c8 00 10 87 1f 41 e0 00 00:04:46.304 READ DMA c8 00 08 7f 1f 41 e0 00 00:04:46.288 READ DMA c8 00 08 77 1f 41 e0 00 00:04:46.288 READ DMA c8 00 08 6f 1f 41 e0 00 00:04:46.288 READ DMA Error 21 occurred at disk power-on lifetime: 12569 hours (523 days + 17 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 60 c7 cd 06 e0 Error: UNC 96 sectors at LBA = 0x0006cdc7 = 445895 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 c7 cd 06 e0 00 00:04:40.496 READ DMA c8 00 f0 cf bd 06 e0 00 00:04:40.496 READ DMA c8 00 08 c7 bd 06 e0 00 00:04:40.480 READ DMA c8 00 10 bf 00 0c e0 00 00:04:40.480 READ DMA c8 00 10 d7 53 1b e0 00 00:04:40.480 READ DMA Error 20 occurred at disk power-on lifetime: 11640 hours (485 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 59 22 b6 ec Error: UNC 8 sectors at LBA = 0x0cb62259 = 213262937 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 59 22 b6 ec 00 01:38:16.640 READ DMA 27 00 00 00 00 00 e0 00 01:38:16.624 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 01:38:16.624 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 01:38:16.624 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 01:38:16.624 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 19 occurred at disk power-on lifetime: 11640 hours (485 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 59 22 b6 ec Error: UNC 8 sectors at LBA = 0x0cb62259 = 213262937 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 59 22 b6 ec 00 01:38:15.616 READ DMA 27 00 00 00 00 00 e0 00 01:38:15.600 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 01:38:15.600 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 01:38:15.600 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 01:38:15.600 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 11634 - # 2 Short offline Completed without error 00% 11186 - # 3 Short offline Completed without error 00% 11186 - # 4 Short offline Completed without error 00% 11182 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.